Hello All,
In my current build I have encountered a problem the first time.
When I attached the wings there was a series of 'depressions' between the two parts.
Despite applying a fair bit of filler they are still quite deep.
Is there another, better, way to fill such large areas so that they are level?
Thanks,
Steve
What Is the Best Way To Handle This Please?
- JamesPerrin
- Looks like his avatar
- Posts: 13669
- Joined: April 5th, 2011, 8:09 pm
- Location: W. Yorkshire
- Contact:
Re: What Is the Best Way To Handle This Please?
What filler did you use and what did you sand it back with?
If the filler is soft like Green Stuff and the sanding medium coarse it can 'dig' filler out. Also note that most fillers shrink as they dry and so you need to overfill or re-apply before sanding. A coat for grey or silver paint once you have sanded can help you see if you have fixed the issue or need to re-apply again.
If the filler is soft like Green Stuff and the sanding medium coarse it can 'dig' filler out. Also note that most fillers shrink as they dry and so you need to overfill or re-apply before sanding. A coat for grey or silver paint once you have sanded can help you see if you have fixed the issue or need to re-apply again.
Classic British Kits SIG Leader Better to fettle than to fill
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
Re: What Is the Best Way To Handle This Please?
Hello James,
I used Squadron White Putty, sanded back with various grades of paper/cloth starting with 400 and finishing with 4000.
The problem I found was that because the depression was such an irregular shape and the putty didn't actually bond with the plastic it was easily sanded away from the outer edge leaving a 'lip' around it, if that makes sense.
I didn't really need the silver paint, the fault is still glaringly obvious. It was my inability to actually fill it properly in the first place that was the root of the problem.
Regards,
Steve
I did have a tube of Revell filler which seemed to 'grip' to the plastic more, but it just went hard in the tube, so perhaps something more aggressive than Squadron White might be the way to go?
I used Squadron White Putty, sanded back with various grades of paper/cloth starting with 400 and finishing with 4000.
The problem I found was that because the depression was such an irregular shape and the putty didn't actually bond with the plastic it was easily sanded away from the outer edge leaving a 'lip' around it, if that makes sense.
I didn't really need the silver paint, the fault is still glaringly obvious. It was my inability to actually fill it properly in the first place that was the root of the problem.
Regards,
Steve
I did have a tube of Revell filler which seemed to 'grip' to the plastic more, but it just went hard in the tube, so perhaps something more aggressive than Squadron White might be the way to go?
- DavidWomby
- Modelling Gent and Scholar
- Posts: 11750
- Joined: May 1st, 2011, 8:09 pm
- Location: Florida, USA
Re: What Is the Best Way To Handle This Please?
I find that I often apply too much pressure when sanding and it results in 'hollowing out' a dished area where the filler is. Could that be part of the problem? It's at its worst for me if I sand using sandpaper and a finger and less of a problem if I use a sanding stick or a Flex-I-File so I am not applying pressure right over the area of filler.
David
David
- JamesPerrin
- Looks like his avatar
- Posts: 13669
- Joined: April 5th, 2011, 8:09 pm
- Location: W. Yorkshire
- Contact:
Re: What Is the Best Way To Handle This Please?
Hot filler such as White Stuff can dry out in the tube and if it's chalky when you apply it, and not wet, it won't bond.
I've largely given up trying to use "quick" fillers and gone back to Milliput. Yes it takes overnioght to harden but as my modelling sessions are never long enough for even the quick ones to dry it is not an issue. Very good bond unless the surface is greasy (no kebabs while modelling!)
I've largely given up trying to use "quick" fillers and gone back to Milliput. Yes it takes overnioght to harden but as my modelling sessions are never long enough for even the quick ones to dry it is not an issue. Very good bond unless the surface is greasy (no kebabs while modelling!)
Classic British Kits SIG Leader Better to fettle than to fill
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
Re: What Is the Best Way To Handle This Please?
Thanks James,dwomby wrote:I find that I often apply too much pressure when sanding and it results in 'hollowing out' a dished area where the filler is. Could that be part of the problem? It's at its worst for me if I sand using sandpaper and a finger and less of a problem if I use a sanding stick or a Flex-I-File so I am not applying pressure right over the area of filler.
Thanks David,
I have the same problem, and have just bought a Flex-I-File, which has been of great use on my current kit, as almost every part needed sanding to some degree or other.
JamesPerrin wrote:Hot filler such as White Stuff can dry out in the tube and if it's chalky when you apply it, and not wet, it won't bond.
I've largely given up trying to use "quick" fillers and gone back to Milliput. Yes it takes overnioght to harden but as my modelling sessions are never long enough for even the quick ones to dry it is not an issue. Very good bond unless the surface is greasy (no kebabs while modelling!)
So, it may just be that the filler I am using is too old and needs replacing, and at the moment, a kebab seems much more appealing than the He111.
Regards,
Steve