The Unofficial Airfix Modellers' Forum
http://uamf.org.uk/

stuff that makes plastic glue un-stick?
http://uamf.org.uk/viewtopic.php?f=93&t=16145
Page 1 of 1

Author:  Crashpilot [ October 3rd, 2017, 2:55 pm ]
Post subject:  stuff that makes plastic glue un-stick?

Somewhere on some kind of forum, I read about stuff that can make polystyrene glue loose.
I bought 2 second-hand kits, just for cannibalizing them for spares.
But that guy used so much glue on it, that I have to make the plastic crack, to get the spares out!
I remember faintly that it´s something that car mechanics use to un-weld things, and that you shouldn´t leave it
on the plastic for too long, cause it´s quite aggressive, and makes the plastic melt, after a while.

Author:  iggie [ October 3rd, 2017, 4:41 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

Not sure about anything that will 'unstick' plastic that has effectively been welded by liquid poly or similar, but I have had limited success using liquid glues (Humbrol Liquid Poly, Tamiya Extra Thin etc.) to melt a welded join and allow me to tear it apart without too much damage...but then only on recently glued joins, not anything of any age.

A razor saw might be more use? :grin:

Author:  Crashpilot [ October 3rd, 2017, 8:56 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

...a razor saw in most cases, yes.
But I want to save some wheel wells from a Revell Spitfire wreck, to transplant them into a Heller Spitfire.
But the former owner glued the wheels in with a big gulp of liquid poly, I´d saw the well into shreds, then.

Author:  Gregers [ October 3rd, 2017, 10:07 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

You may be out of luck in that case as liquid poly melts the parts together, the more glue used the more it will melt.i would just try gently prying the wheel out moveng around it to break the join. I personally don't know of any product that will seperate the join unfortunately. Sorry I can't be of more help.

All the best.

Greg

Author:  SJPONeill [ October 4th, 2017, 1:56 am ]
Post subject:  Re: stuff that makes plastic glue un-stick?

Put the model in the freezer overnight - the extreme cold will make the joins more brittle than the plastic and you can (usually) snap the pieces apart along the weld...you still have some cleaning up to do and there's no guarantees especially with smaller parts but it's the only way that i know that doesn't have a higher attendant risk of simply dissolving the whole thing into a gooey mess...

Author:  Crashpilot [ October 4th, 2017, 8:51 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

Thank you, I´ll try that ;-)

Author:  Old_Tonto [ October 11th, 2017, 9:55 am ]
Post subject:  Re: stuff that makes plastic glue un-stick?

Did it work crash?

Author:  Crashpilot [ October 14th, 2017, 6:03 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

...it helped me to take out one of the wheels, the other one´s still stuck inside.
Now I put the model upside down into the freezer, before doing so, I let some drops of water into the wheel well -
I hope the freezing water will weaken the join!

Author:  Crashpilot [ December 5th, 2017, 6:53 pm ]
Post subject:  Re: stuff that makes plastic glue un-stick?

...after leaving it in the freezer for almost 2 months, I remembered something....
that was a good tip! Wheel came out very easily, by lifting it out with a tweezer.
Before the freezer trick, I was only damaging the surface detail, and nuthin happened!

Page 1 of 1 All times are UTC [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/