Page 1 of 1

Hobby Boss Sea Hawk

Posted: January 5th, 2014, 8:55 pm
by bluesteel
Right... I'm now going to take a 'low hanging fruit' approach to completing the 'started-not-finished' stash. It looks like the Hobby Boss Sea Hawk is now the closest to being finished, just the u/c, canopy and decals to go. So it's up next:

Image

Re: Hobby Boss Sea Hawk

Posted: January 7th, 2014, 12:42 am
by shangos70
I've heard the white on the roundels isn't very opaque, hope it doesn't show the demarcation through the middle.

Re: Hobby Boss Sea Hawk

Posted: January 7th, 2014, 1:26 pm
by bluesteel
shangos70 wrote:I've heard the white on the roundels isn't very opaque, hope it doesn't show the demarcation through the middle.
Thanks for the warning. I'll see how they go. If needs be I think I have the Xtradecal Sea Hawk set around somewhere, so I could replace with those if required.

Re: Hobby Boss Sea Hawk

Posted: January 7th, 2014, 6:20 pm
by Dazzled
I've built the Indian Navy version and had no issues with the decals.

The fit of the intakes and trying to sand out the fuselage lateral seam yes :oops: , but the decals were fine.

Re: Hobby Boss Sea Hawk

Posted: January 15th, 2014, 8:06 pm
by TomW
Don't go mentioning that lateral seam Darryl :evil: it still brings me nightmares, looking good Julian and nice to see the Seahawk in the later EDSG/white colours.

Regards

Tom

Re: Hobby Boss Sea Hawk

Posted: January 16th, 2014, 10:52 pm
by bluesteel
Up on it's u/c. Pilot figure next, I think I'll use one from the Revell NATO Pilots set, should be enough room in the office.

Image

Re: Hobby Boss Sea Hawk

Posted: January 19th, 2014, 11:47 am
by bluesteel
Pilot now ready to climb onboard...

Image

Re: Hobby Boss Sea Hawk

Posted: January 19th, 2014, 12:14 pm
by bluesteel
Decals going on. They are reasonably opaque, but the ridge formed by the boundary of the dark grey that I put on over the white does show through. Not a lot I dan do about that unfortunately. Fortunately only noticable close up or when using flash photo.

Image

Re: Hobby Boss Sea Hawk

Posted: January 19th, 2014, 8:09 pm
by bluesteel
Decals all on and pilot installed:

Image

Not putting the large serials on top of the wings as it looks like Hobby Boss got it wrong as there are no photos of Seahawks from that carrier and date sporting top serials, only roundels.

Canopy framing to do, drop tanks and aerials to to attach and it'll be finished.

Re: Hobby Boss Sea Hawk

Posted: January 20th, 2014, 1:53 am
by JohnRatzenberger
Getting there ....

Re: Hobby Boss Sea Hawk

Posted: January 20th, 2014, 9:33 pm
by bluesteel
jRatz wrote:Getting there ....
Yes. Slow but steady :-D

Re: Hobby Boss Sea Hawk

Posted: January 20th, 2014, 9:36 pm
by bluesteel
Canopy and fuel tanks attached. Now just the last part of the front canopy framing and aerials to go.

Image

Re: Hobby Boss Sea Hawk

Posted: January 20th, 2014, 10:49 pm
by bluesteel
All done :grin:


Image


Insufficient nose weight has necessitated a small tail stand to keep the nose on the deck. Other than that quite a pleasant build.

Re: Hobby Boss Sea Hawk

Posted: January 21st, 2014, 1:04 am
by PaulBradley
Very nice, Julian!