Which Compressor?
Which Compressor?
I am sure this is a question that gets bandied about a lot, please indulge me! I am finally in a position to afford a modest compressor, somewhere in the £70-£100 range and am looking for a decent model for a beginner with an airbrush. Does anybody have suggestions? They would be much appreciated. I have spent a long time perusing ebay and amazon etc. but it is quite an overwhelming task choosing one!!!
Thanks all
Thanks all
My modelling Facebook page: https://www.facebook.com/mattscalemodels/
Re: Which Compressor?
Here's what I use...
A Wolfair - cost £60 from Screwfix. Industrial in capacity, it has a large tank, regulator, safety valve and gauge. It has served me well for nigh on 10 years
A Wolfair - cost £60 from Screwfix. Industrial in capacity, it has a large tank, regulator, safety valve and gauge. It has served me well for nigh on 10 years
All models are equal. Some models are more equal than others.
Airfix Tribute Forum
Airfix Tribute Forum
Re: Which Compressor?
Great thanks! Could I ask how loud it is? Unfortunately I live in a block of flats so noise is an issue. I wouldn't have thought it would be that bad, but the word 'industrial' was there so I thought I had best check!!!
My modelling Facebook page: https://www.facebook.com/mattscalemodels/
-
- The Bug Has Well And Truly Bitten
- Posts: 271
- Joined: April 20th, 2016, 12:58 am
- Location: Portimão, Algarve, Portugal
Re: Which Compressor?
Something like this is good: http://www.artesanialatina.net/EN/airbr ... iltre.html;
It's silent enough for use in a flat surrounded by neighbors... at least till 8.30, 9 p.m.
Good luck!
It's silent enough for use in a flat surrounded by neighbors... at least till 8.30, 9 p.m.
Good luck!
Re: Which Compressor?
My neighbours don't complain, but then I don't use it during anti-social hoursSBO wrote:Could I ask how loud it is?
Its a bit noisy but not for long at all - it fills the tank and you spray from the reservoir
All models are equal. Some models are more equal than others.
Airfix Tribute Forum
Airfix Tribute Forum
- iggie
- Modelling Gent and Scholar
- Posts: 23438
- Joined: July 31st, 2013, 11:04 am
- Location: North Somercotes, Lincolnshire
- Contact:
Re: Which Compressor?
This is similar to the one I use;
http://www.ebay.co.uk/itm/Airbrush-Comp ... rkt%3D1%26
No reservoir but you would struggle to hear it from a dozen feet away.....but any compressor needs to be stood on something to absorb the vibration as that is usually the source of noise heard by neighbours. Stand it on a thick foam sheet or similar and you should be ok
http://www.ebay.co.uk/itm/Airbrush-Comp ... rkt%3D1%26
No reservoir but you would struggle to hear it from a dozen feet away.....but any compressor needs to be stood on something to absorb the vibration as that is usually the source of noise heard by neighbours. Stand it on a thick foam sheet or similar and you should be ok
Best wishes
Jim
If you can walk away from a landing, it's a good landing. If you use the airplane the next day, it's an outstanding landing
"Never put off till tomorrow, what you can do the day after tomorrow"
Jim
If you can walk away from a landing, it's a good landing. If you use the airplane the next day, it's an outstanding landing
"Never put off till tomorrow, what you can do the day after tomorrow"
Re: Which Compressor?
Excellent thanks chaps! Ok so a novice question coming up - reservoir or no reservoir? Does a compressor with no reservoir make less noise? Is a reservoir something that makes an appreciable difference to a beginners airbrushing? And lastly, how loud roughly would a 'loud' compressor be - i.e. is it vacuum cleaner loud?
Sorry - I am sure you can tell I have never even seen a compressor let alone used one!!!
Sorry - I am sure you can tell I have never even seen a compressor let alone used one!!!
My modelling Facebook page: https://www.facebook.com/mattscalemodels/
- iggie
- Modelling Gent and Scholar
- Posts: 23438
- Joined: July 31st, 2013, 11:04 am
- Location: North Somercotes, Lincolnshire
- Contact:
Re: Which Compressor?
Interesting question....mine is a non-reservoir type, so the compressor runs as long as I am on the trigger; I would say it is half the sound output of a dyson upright vacuum cleaner.
I can't speak for the reservoir types....
I can't speak for the reservoir types....
Best wishes
Jim
If you can walk away from a landing, it's a good landing. If you use the airplane the next day, it's an outstanding landing
"Never put off till tomorrow, what you can do the day after tomorrow"
Jim
If you can walk away from a landing, it's a good landing. If you use the airplane the next day, it's an outstanding landing
"Never put off till tomorrow, what you can do the day after tomorrow"
Re: Which Compressor?
I have a non-reservoir Paasche compressor. Very quiet. So quiet I put a tag on it to remind myself to turn it off. $90.00USD. Been using it for around four years now.
Besting 60 years of mediocre building of average kits in the stand off scale
Re: Which Compressor?
That sounds ideal for my purposes - could I trouble you for a model number? Thanks!
My modelling Facebook page: https://www.facebook.com/mattscalemodels/
Re: Which Compressor?
Realized I could have added this above. A senior moment.
http://www.paascheairbrush.com/discount-class/g/D500SR;
This is the Company ad but mine was obtained via my LMS who, in turn, obtained it from Stevens International.
Good luck.
http://www.paascheairbrush.com/discount-class/g/D500SR;
This is the Company ad but mine was obtained via my LMS who, in turn, obtained it from Stevens International.
Good luck.
Besting 60 years of mediocre building of average kits in the stand off scale
Re: Which Compressor?
Haha no problem! I looked into it and unfortunately that particular company's products retail for a vastly inflated price on this side of the Atlantic, which puts them out of my price range. In the end I plumped for a nice cheap and cheerful compressor with excellent reviews on Amazon, the thinking being it will allow me to get acquainted with the intricacies of airbrushing before hopefully upgrading in the near future.
So I must say thanks to all in this thread, your advice has been incredibly helpful! I doff my cap to you all
So I must say thanks to all in this thread, your advice has been incredibly helpful! I doff my cap to you all
My modelling Facebook page: https://www.facebook.com/mattscalemodels/
-
- Modelling Gent and Scholar
- Posts: 3325
- Joined: November 4th, 2012, 11:28 am
- Location: The Netherlands
- Contact:
Re: Which Compressor?
A reservoir acts as a pressure stabilisor and buffer. The pumps on many compressors do not generate an even pressure, but rather very rapid peaks (think pistons in an engine). The reservoir evens this out. Also, the pump is the part that makes the noise, and you don't want a loud compressor like the one I have running while working. You either want a quiet hobby model, that can have the pump running while working but either has a more advanced pump design, or a small reservoir, or a more basic pump with a large reservoir so you can shut it off while working.SBO wrote:Ok so a novice question coming up - reservoir or no reservoir? Does a compressor with no reservoir make less noise?
No. You want even, steady pressure, and a reservoir is but one way of obtaining it.Is a reservoir something that makes an appreciable difference to a beginners airbrushing?
Very. As in, don't stick around in the same room without hearing protection loud.And lastly, how loud roughly would a 'loud' compressor be - i.e. is it vacuum cleaner loud?
My current compressor is a big powerfull brute like Ratch's, but with a much larger tank. It's designed to drive power tools or fill tyres and such, and makes a monstrous racket. On the other hand, on a full day spent mostly on airbrush work, it runs maybe 4 times, while I grab a mug of tea and/or some breath.
Before that one, I had a smaller unit without a reservoir that ran all the time (at roughly vacuum cleaner noise levels). Didn't like the noise when working, and didn't like the fact that it ran hot and would shut down at inconvenient times for cooling. I don't think this was a very good compressor..
I've also been in the room with an airbrushing workshop going on, meaning about a dozen little compressors chugging along, and it didn't feel like a noisy room. From what I've read so far, this is the sort of compressor that would fit your needs best. Noise level, max pressure, and capacity should be somewhere in the specs; compare those to get an idea of what you might need.
Also, a small word of caution: the glitzy folders are almost certain to show people cheerfully airbrushing without any breathing protection. This is plain stupid. Put something between your lungs and paint, even when working with acrylics (the solvent might not be a problem, but the resin and pigments are). Also keep in mind that the paint will fly anywhere near your workarea; it may be just a very slow buildup, but you will paint the room..
Re: Which Compressor?
I started out with a Tamiya Sprayworks Compressor and basic Airbrush.
http://www.tamiya.com/english/products/ ... c_comp.htm;
It was very good and as long as you stuck to Tamiya or Gunze paints it worked very very well. I painted a lot of models with it and at some point upgraded the basic airbrush to a more 'advanced' model also a Tamiya.. Its not overly noisy and is quite compact.
http://www.tamiya.com/english/products/ ... r_fine.htm;
This runs fine with the Tamiya basic compressor.
The reality is a combination of the Basic Tamiya gun and this Airbrush could probably spray pretty much any model to a reasonable standard.
If you get into more exotic paint types such as Alclad and Lacquers then being able to control the output air pressure feeding the airbrush is handy. However for the other 97.5% of modelling this will probably be sufficient.
The Tamiya sprayworks set is non adjustable and outputs a fixed air pressure constantly. It's what's known as a constant loss system.
I liked it because I wanted to paint models not become a de-facto expert on: compressors, air pressure, water traps, air hose fittings and dB ratings of compressors.
There is one for sale on Ebay Uk currently
http://www.ebay.co.uk/itm/Tamiya-Model- ... SwPhdU-Hby;
No connection to the seller etc.. I have the older version of this which is pretty quiet. This version is much more quiet.
I currently use a small reservoir compressor like Rob and Richard with an outlet pressure regulator water trap and all the gubbins. Mainly because I now run a series of classic Holbein Double Action Airbrushes and want to paint with Alcald and lacquers etc which benefit from lower outlet air pressures than the Tamiya compressor can deliver.
However I'd happily use my Sprayworks again. The reality is there is no 'buy this and it will work' type answer for the question you have asked. However IMHO the Tamiya Sprayworks gives the most complete answer to the requirements you have and is not overly expensive..
HTH
Cheers
Gadfly
http://www.tamiya.com/english/products/ ... c_comp.htm;
It was very good and as long as you stuck to Tamiya or Gunze paints it worked very very well. I painted a lot of models with it and at some point upgraded the basic airbrush to a more 'advanced' model also a Tamiya.. Its not overly noisy and is quite compact.
http://www.tamiya.com/english/products/ ... r_fine.htm;
This runs fine with the Tamiya basic compressor.
The reality is a combination of the Basic Tamiya gun and this Airbrush could probably spray pretty much any model to a reasonable standard.
If you get into more exotic paint types such as Alclad and Lacquers then being able to control the output air pressure feeding the airbrush is handy. However for the other 97.5% of modelling this will probably be sufficient.
The Tamiya sprayworks set is non adjustable and outputs a fixed air pressure constantly. It's what's known as a constant loss system.
I liked it because I wanted to paint models not become a de-facto expert on: compressors, air pressure, water traps, air hose fittings and dB ratings of compressors.
There is one for sale on Ebay Uk currently
http://www.ebay.co.uk/itm/Tamiya-Model- ... SwPhdU-Hby;
No connection to the seller etc.. I have the older version of this which is pretty quiet. This version is much more quiet.
I currently use a small reservoir compressor like Rob and Richard with an outlet pressure regulator water trap and all the gubbins. Mainly because I now run a series of classic Holbein Double Action Airbrushes and want to paint with Alcald and lacquers etc which benefit from lower outlet air pressures than the Tamiya compressor can deliver.
However I'd happily use my Sprayworks again. The reality is there is no 'buy this and it will work' type answer for the question you have asked. However IMHO the Tamiya Sprayworks gives the most complete answer to the requirements you have and is not overly expensive..
HTH
Cheers
Gadfly