Skypirate's Airfix-Plastyk 1/72 blended Hunter *FINISHED*
- skypirate
- Modelling Gent and Scholar
- Posts: 7303
- Joined: May 1st, 2011, 6:13 am
- Location: Port Macquarie, Australia
Skypirate's Airfix-Plastyk 1/72 blended Hunter *FINISHED*
I hope I have not bitten off more than I can chew!
I have a few each of the Airfix and FROG 1/72 Hunters in the stash, and each has shape problems. Paul Bradley, in his SAM Hunter volume suggested that the front-end of the Plastyk kit and the rear end of the Airfix kit might solve each other's problems. Of course, it will not be as straightforward as that. Even though the Plastyk kit wings are of good shape and size, I find them lacking in aerofoil section (too flat), so I am not sure which way I will jump there.
Here we go:
The Plastyk wings will be a highly convenient choice for this set of parts! The Airfix spine needs to be fattened slightly, and the rear fuselage girth reduced by about 1 mm thickness at the top (giving up that 1 mm to the spine). And the Plastyk nose needs to be slimmed down just a bit halfway between the windscreen and the tip of the nose.
Sounds good in theory!
Cheers,
David
I have a few each of the Airfix and FROG 1/72 Hunters in the stash, and each has shape problems. Paul Bradley, in his SAM Hunter volume suggested that the front-end of the Plastyk kit and the rear end of the Airfix kit might solve each other's problems. Of course, it will not be as straightforward as that. Even though the Plastyk kit wings are of good shape and size, I find them lacking in aerofoil section (too flat), so I am not sure which way I will jump there.
Here we go:
The Plastyk wings will be a highly convenient choice for this set of parts! The Airfix spine needs to be fattened slightly, and the rear fuselage girth reduced by about 1 mm thickness at the top (giving up that 1 mm to the spine). And the Plastyk nose needs to be slimmed down just a bit halfway between the windscreen and the tip of the nose.
Sounds good in theory!
Cheers,
David
- Clashcityrocker
- Modelling Gent and Scholar
- Posts: 10827
- Joined: May 1st, 2011, 12:31 am
- Location: Adelaide. South Australia
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
You're just the man for the job David
Nigel
Nigel
- DavidWomby
- Modelling Gent and Scholar
- Posts: 11766
- Joined: May 1st, 2011, 8:09 pm
- Location: Florida, USA
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
This should be good, David. I've wondered how that combination would look. Looking forward to watching your build.
David
David
- JamesPerrin
- Looks like his avatar
- Posts: 13695
- Joined: April 5th, 2011, 8:09 pm
- Location: W. Yorkshire
- Contact:
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Got your work cut out on this one!
Classic British Kits SIG Leader Better to fettle than to fill
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
(2024 A:B 5:2) (2023 13:8:7) (2022 21:11) (2021 15:8) (2020 8:4:4)
- Old_Tonto
- Modelling Gent and Scholar
- Posts: 8063
- Joined: May 1st, 2011, 7:41 pm
- Location: Middlesbrough, Peoples Republic of Teesside.
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Proper surgery. Cool.
2023 - A:0 B:0 C:0
Current Projects:
East German Air Force (1956-90)
South African Air Force (1958-93)
Current Projects:
East German Air Force (1956-90)
South African Air Force (1958-93)
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Break out the bone saw. nothing like hacking errr.... doing some surgery on a kit to mend it's ill,s
I agree the Plastyk Hunter's nose does look kind of off.
All the best.
Greg
I agree the Plastyk Hunter's nose does look kind of off.
All the best.
Greg
Two things are infinite: the universe and human stupidity; and I'm not sure about the the universe.
The difference between stupidity and genius is that genius has its limits.
Albert Einstein
The difference between stupidity and genius is that genius has its limits.
Albert Einstein
-
- NOT the sheep
- Posts: 26188
- Joined: November 26th, 2011, 6:11 pm
- Location: Pontefract West Yorkshire
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Excellent, a proper old skool bit of kit bashing. I'm sure you're well up to the challenge, David!
Doing - Tamiya 1/35th Universal Carrier.
Work is the curse of the modelling classes!
IPMS#12300
Work is the curse of the modelling classes!
IPMS#12300
- DavidWomby
- Modelling Gent and Scholar
- Posts: 11766
- Joined: May 1st, 2011, 8:09 pm
- Location: Florida, USA
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
I'm curious, David. Obviously you can't cut off the Plastyk fuselage further forward than you did but is the girth mismatch because the Plastyk fuselage start tapering further forward than your cut or is the the whole of the remaining Plastyk fuselage skinnier than the Airfix one?
David
David
- splash
- Senior Service Rotorhead
- Posts: 13828
- Joined: May 1st, 2011, 11:02 am
- Location: Somerset England
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Now this looks fun I’m going to pull up a chair and watch you do your magic.
My work bench is starting to look like Portsmouth Naval Dockyard.
- skypirate
- Modelling Gent and Scholar
- Posts: 7303
- Joined: May 1st, 2011, 6:13 am
- Location: Port Macquarie, Australia
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
This is slightly encouraging.
Before and after on one side of the spine.
So now I have a deeper spine on one side of the Airfix rear fuselage, to match the Plastyk forward fuselage, and the overall depth of the fuselage is the same.
The hard part is having the patience to do the same on the other side!
Cheers,
David
Before and after on one side of the spine.
So now I have a deeper spine on one side of the Airfix rear fuselage, to match the Plastyk forward fuselage, and the overall depth of the fuselage is the same.
The hard part is having the patience to do the same on the other side!
Cheers,
David
- skypirate
- Modelling Gent and Scholar
- Posts: 7303
- Joined: May 1st, 2011, 6:13 am
- Location: Port Macquarie, Australia
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
So the further I get in this project, the more I realise that the Plastyk kit is basically toy-like. I am going ahead, but I will use many Airfix parts that are less toy-like (wheel doors, wing tanks, pylons). Here we have a view of the many sink holes puttied, the Airfix intake plugs modified to fit (sort of), and the prospective replacement cockpit parts - which will have to be modified.
I have to get the front fuselage sealed up in order to address the overall fuselage join.
It will still be a pretty basic model. If I finish! Couple more in the stash are unlikely to be built. At least they were cheap. The built Airfix kit (either F.6 or FGA.9) does not look too bad, apart from the slightly undernourished nose. And I am quite partial to the FROG Mk.9, even with the slightly portly rear fuselage. I am not ready to discard those in favour of more Revell kits!
Cheers,
David
I have to get the front fuselage sealed up in order to address the overall fuselage join.
It will still be a pretty basic model. If I finish! Couple more in the stash are unlikely to be built. At least they were cheap. The built Airfix kit (either F.6 or FGA.9) does not look too bad, apart from the slightly undernourished nose. And I am quite partial to the FROG Mk.9, even with the slightly portly rear fuselage. I am not ready to discard those in favour of more Revell kits!
Cheers,
David
- DavidWomby
- Modelling Gent and Scholar
- Posts: 11766
- Joined: May 1st, 2011, 8:09 pm
- Location: Florida, USA
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Nice work whittling down the Airfix rear fuselage.
Despite their known issues the Airfix and both Frog kits certainly look the part even built OOB. Just can't park them next to each other as the differences between them really glare out (at least to me).
David
Despite their known issues the Airfix and both Frog kits certainly look the part even built OOB. Just can't park them next to each other as the differences between them really glare out (at least to me).
David
- skypirate
- Modelling Gent and Scholar
- Posts: 7303
- Joined: May 1st, 2011, 6:13 am
- Location: Port Macquarie, Australia
Re: Skypirate's Airfix-Plastyk 1/72 blended Hunter
Thanks, David.
I must be feeling confident about this project. Don't know why!
I have chosen to model the A&AEE Hunter F.6A XE587. Light aircraft Grey overall, with red spine, empennage, canopy trim and wing tanks.
Decals from the spares bank (though this scheme can be found on a decal sheet).
Cheers,
David
I must be feeling confident about this project. Don't know why!
I have chosen to model the A&AEE Hunter F.6A XE587. Light aircraft Grey overall, with red spine, empennage, canopy trim and wing tanks.
Decals from the spares bank (though this scheme can be found on a decal sheet).
Cheers,
David